Knoll Systems HT200 Manual do Utilizador

HT200 Users Manual v1.0 Complies with part 15 of the FCC rules. Operation is subject to: 1. This device may not cau

Connecting Component Video Equipment withYCbCr output jacks to the RGB IN connector You can also connect the video component to the RGB IN connector,

Connecting a PC or Macintosh Connecting a PC or Macintosh to the Projector enables computer images for impressive presentations. • The following disp

Modifying the DIP switch (for Macintosh) setting Modify the DIP switch setting on the MAC cable as shown below. Macintosh adapter cable DIP switch set

Connecting the remote mouse receiver to an IBM PC/AT computer Connect the IBM/Mac connector on the remote mouse receiver and PC's mouse port with

2) Press the POWER ON button on the remote control or the POWER button on top of the unit to turn on the unit. The POWER indicator on top of the uni

7) Change the unit setting to suit to the projecting method and selected source as described in step 4. • Select the type of projection If the pr

Changing computer's video resolutions Depending on your computer's graphic capability, you may be able to select one of several resolutions.

Adjusting the volume of the projector speaker Press VOLUME + to increase the volume or - to decrease. The volume can also be adjusted with the menu op

Menu operation- Selecting the input source with the remote 1) Press MENU. The button lights in red and the main menu appears on the scr

of the selected menu item. value of the selected menu item. Selecting the projection type; Floor, Ceiling, Rear and Front This reorients your image f

IMPORTANT SAFEGUARDS These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefull

Setting "INPUT MODE" to "YCbCr" or Component Video When you have connected the component video (YCbCr) signal output jacks of th

Timing Chart Signal Resolution H. Sync. (kHz) V. Sync. (Hz) Dot Clock (MHz) 1 NTSC 640 x 480 15.734 59.94 - 2 PAL 768 x 576 15.625 50 - 3

Adjusting the clock frequency (PICTURE ADJ) and clock phase (FINE PICTURE) manually When "AUTO PICTURE" is set to "ON," the clock

Storing the most recent “PICTURE ADJ,” “FINE PICTURE,” “H POSITION,” AND “V POSITION” settings You can store the above present settings in the memory.

Adjusting the picture elements The picture elements such as brightness, contrast, white balance, and so on can be adjusted individually for each input

The following three types of gamma modes can be selected according to your preferences: • NORMAL, • NATURAL 1, or • NATURAL 2. 8. Press L-CLICK. 9.

Turning the projector off with on screen functions With the remote control: Press the POWER OFF button a for 2 seconds (the projector will turn off r

Specifications Optical DMD TM Single Chip Digital Micro Device (DMD TM), 800x600 dots Lens Manual zoom, manual focus F3.0 f =27.5 to 35.75mm Lamp

Troubleshooting This section helps you resolve problems while setting up or using your projector. Common Problems & Solutions Problem Check The

When the STATUS indicator on the projector keypad lights or blinks Status Light Message Condition Status OFF Normal On Continually The projector lam

Table of Contents 2 IMPORTANT SAFETY INFORMATION 3 Table of contents 4 Basic information 5 Features 5 Remote control 6 Terminal connections 7

Lamp housing replacement procedure 1. Switch off the main power and unplug the power cord. 2. Wait at least one hour for the lamp to cool. 3. Turn th

Basic HT200 Information Congratulations On Your Purchase of the HT200 Projector! The HT200 is one of the very best Projectors available today. The

Remote Control Inserting the batteries 1) Press firmly and slide the battery cover off. 2) Insert the supplied two batteries (size AA/R6). Ensure th

Terminal Connection Panel Projector Part Identification 6

Installation The distance from the projector lens to the screen determines to the size of the projected image, therefore, you need to consider the pla

Use the following information to position the projector. Horizontally the projector needs to be positions with the lens-centered left to right Projec

Connecting Video Equipment You can connect a document camera, VCR, laser disc player, and DVD player, etc. Connecting to the VIDEO IN VIDEO/S-VIDEO J